1550 Cobb Industrial Dr. | P.O. Box 9098 | Marietta, GA 30065-2098
770-425-1355 (Phone) | 770-425-1354 (Fax) | info@alliedcorrosion.com (Email)
©2018 Allied Corrosion. All rights Reserved.
Made with ❤ by Mighty Good Marketing
EDI Impressed Current Probe Anode (Model AR)
Model Designation
Specify as EDI Model AR-asd-G.L.TTT where
a = active surface: M for mixed metal oxide or P for platinum
s = substrate: T for titanium or N for niobium
d = rod diameter, inches: 3 for 0.375, 5 for 0.50, 7 for 0.75
G = standoff length, inches: 1 to 9 in 1 inch increments
L = active length, inches: 1 to 9 in 1 inch increments
TTT = micro- inches platinum: 100, 150, 200, 250, 300, or electrolyte for mixed metal oxide: F, B, or S for Fresh, Brackish or Salt water.
EDI Probe Anodes
Impressed Current Probe Anodes specifically designed for Immersion Applications
Titanium or Niobium Substrate and MMO or Platinum Coatings Available
Anode Description
Model AR is a thru-wall impressed current probe anode used to protect condenser waterboxes, waterfront structures, storage tanks and other wetted surfaces. It features a resilient mount between the anode rod and the fiberglass reinforced epoxy stand-off. Anode rods are typically 3/8″ or 1/2″ diameter with 2-9″ active and 1-9″ standoffs. Probes are best where current to a remote location is required. Platinum or Mixed Metal Oxide (MMO) coatings can be applied that provide 20 or more years of service life. Probe anodes are intended for use at flow rates of less than 15 ft/sec (4.5 m/sec) and pressures lower than 150 psi (1 MPa).
Sizing and Number of Anodes
Proper cathodic protection design requires that adequate current be delivered where needed. Therefore, both the number of anodes and their location within the structure are important. Selection of rod diameter, standoff length and active length are based on many factors related to the conditions within the structure. From a cost perspective it is optimal to use the smallest diameter and shortest length rod with the necessary amount of coating to achieve the required design life while maintaining the objectives.
Substrate Selection
Titanium and Niobium are used as coating substrates for anodes because they form oxide films that prevent them from corroding in nature. Titanium is the most widely used. It is acceptable for all applications where the voltage between it and the electrolyte is below 10V. It is the only substrate to which either MMO or Platinum can be applied. Niobium is used for those applications where the voltage at its surface is expected to exceed 10V. Only Platinum can be applied to its surface.
Typical Applications
- Condenser Waterboxes
- Waterfront Structures
- Pump Housings
- Sewage Treatment Tanks
Features
- Platinum(Pt) or mixed metal oxide (MMO) surface coatings
- Full resilient mount in glass reinforced epoxy and polyurethane
Diagrams of Model AR7, AR10 and AR12 Anodes
Other Similar Products
Related products
-
- Anotec, Anodes, Cathodic Protection
Anotec Solid Stick Anodes
- Add To Quote tr This product has multiple variants. The options may be chosen on the product page
-
- Anotec, Anodes, Cathodic Protection
Anotec Small and Specialty Anodes
- Add To Quote tr This product has multiple variants. The options may be chosen on the product page
Learn About Our Services
Learn about our
pipeline integrity
Services
Learn about our
cathodic protection
Engineering Services
Learn about our
A/C Mitigation
Engineering Services
Learn about our
field services
Learn about our
surveying services