1550 Cobb Industrial Dr. | P.O. Box 9098 | Marietta, GA 30065-2098
770-425-1355 (Phone) | 770-425-1354 (Fax) | info@alliedcorrosion.com (Email)
©2018 Allied Corrosion. All rights Reserved.
Made with ❤ by Mighty Good Marketing
PSI Model R Graduated Cone
Model “R” End Seals simplify stocking. Only five (5) end seal sizes will accommodate casings from 4″ to 24″ in diameter with all applicable carrier pipe sizes designated on the unique graduated cone “carrier pipe” end. Made of 1/8″ thick, synthetic rubber for long life and durability, these end seals are designed to last for the life of the piping system.
PSI Model R Graduated Cone End Seals and Night Caps
Description
Model R Graduated Cone End Seals are available in five (5) different sizes to accommodate a wide range of carrier/casing diameter combinations. A unique cone design, with molded-in dimensions, are easily cut to size for a correct fit on the carrier pipe. Stainless steel bands are included for clamping the Model R end seal to both casing and carrier pipes.
Model R End Seals are manufactured from 1/8″ (3.18mm) thick high quality EPDM rubber, Model R end seals are extremely robust, resistant to a wide variety of environmental conditions and may be used to prevent the ingress of moisture and soil into the annular space between carrier and casing pipes.
Benefits and Features
- Low storage costs, only five end seal sizes to accommodate casings from 4″ to 24″ in diameter with all applicable carrier pipe sizes.
- Quick and easy Installation
- Manufactured from 1/8″ (3.18mm) thick high quality EPDM rubber.
- Casing night cap prevents entry of debris and animals during install.
- Sizes are clearly printed on sleeve to simplify cutting to the correct size.
- Designed to last for the life of the piping system
- Stainless steel bands for clamping both ends of end seal provided.
- May be used for new installations.
Material Specifications
| Material | EPDM 60 | ||
| Thickness | 1/8″ (3.18mm) | ||
| Color | Black | ||
| Temperature | 250°F (121°C) | ||
| Hardware | 304 Stainless Steel Bands w/Worm Screws |
||
| Sizing | Per Customer’s Specifications |
||
| Standard casing end seals are designed for below ground use. For above grade applications, please contact Allied Corrosion Industries, Inc. |
|||
Typical Application
Installation
Simply cut the seals at the closed end to the measured external diameter of the carrier pipe. Note: The printed sizes are marked on the end seals.) Push the end seal over the outside of the casing pipe and the carrier pipe and fasten with the included stainless steel bands.
- Prepare outside surfaces by removing dirt from casing and carrier pipe.
- After carrier pipe is inserted into casing, slide small end of end seal over the carrier pipe with stainless steel banding clamp. Large end should face casing.
- Position large end of end seal over the casing pipe.
- Position banding clamp approximately 1″ from the end of the casing pipe and then tighten onto the end seal.
- Fold end seal in an S shape so it will extend into the casing.
- Position banding clamp approximately 1″ from the end of the end seal on the carrier pipe and then tighten. (Make sure the end seal is folded into the casing, to relieve stress during backfilling and allow for expansion and contraction movement.)
- Repeat Steps 1, & 3 – 6 on other end of casing.
Warranty
Manufacturer’s warranty statement will be supplied upon request to Allied Corrosion Industries, Inc.
How to Order
To order Model R End Seals, please indicate the following:
- Quantity
- Carrier Pipe O.D.
(Type and coating thickness if applicable.) - Casing Pipe O.D.
(Type and coating thickness if applicable.) - Select the correct size Model R using charts below.
Typical Specification
Model R end seals shall be manufactured from a minimum 1/8″ thick synthetic rubber. Banding clamps are to be 304 stainless steel with worm screws. End Seals shall be PSI Model R as manufactured by PSI-Pipeline Seal and Insulator, Inc., Houston, TX. to ISO 9001:2000 standards. A copy of current ISO 9001:2000 registration shall be provided with material submittal.
Choosing the right size Model R
There are five sizes from which to choose
- Select the appropriate end seal for your casing pipe O.D. using the colored bars below.
- Verify that your carrier pipe O.D.is within the cone’s diameter range.
Other Similar Products
Related products
Learn About Our Services
Learn about our
pipeline integrity
Services
Learn about our
cathodic protection
Engineering Services
Learn about our
A/C Mitigation
Engineering Services
Learn about our
field services
Learn about our
surveying services